Cost calculator
Asphalt Driveway Cost in Texas
Texas installed pricing runs $6.65 to $14.25 per square foot — about 5% below the national average. Enter your driveway size for a local estimate.
Your project
Tight, steep or long-haul sites cost more because the paver and trucks work slower.
Estimated Texas driveway cost
$3,192 – $6,840
- Area
- 480 sq ft
- Most likely price
- $4,560
- TX price per sq ft
- $6.65 – $14.25
- Asphalt required
- 8.7 tons
- Demolition included
- None
Prices are national planning averages. Asphalt is tied to crude oil and freight costs, so your local quote can land well outside this range. Always confirm with a paving contractor before budgeting. Most Texas contractors also apply a mobilisation minimum of roughly $1,900.
The shareable link reopens this calculator with your exact inputs.
Asphalt driveway prices in Texas
A new asphalt driveway in Texas typically runs $6.65 to $14.25 per square foot installed, with most homeowners landing near $9.50. That puts TX about 5% below the national average.
Huge contractor supply and cheap aggregate, though metro demand is rising fast.
A standard two-car driveway of 600 square feet therefore costs roughly $3,990 – $8,550 in Texas, and a 1,000 square foot driveway roughly $6,650 – $14,250.
Southern Heat build spec for Texas
Texas sits in a Southern Heat zone, where the pavement is attacked by highly expansive clay soils and sustained 100 °F summer temperatures. Expansive clay in the east and extreme heat statewide — base moisture control is critical.
That translates into a concrete specification: 6 to 8 inches of flex base (crushed limestone), normally TxDOT Grade 1-2 crushed limestone flex base, under the asphalt. On the mix side, Stiff PG 70-22 binder against high-temperature deformation, over stabilised subgrade.
The practical paving season in Texas is Year-round. Plants close outside that window in most of the state, and asphalt placed on frozen or saturated subgrade will not compact properly no matter how good the crew is.
What moves the number most
Three things dominate: demolition of whatever is there now, base depth, and access. Tearing out old concrete adds roughly $2.85 per square foot in Texas. Difficult access — steep grades, tight gates, hand work around obstacles — adds about 25%.
Thickness matters less than people expect. Going from 2" to 3" of surface course adds only about 8% per inch to the total job, because mobilisation, grading and base are the same either way. It is nearly always worth paying for.
Getting quotes in Texas
Get three written quotes and make each one state compacted asphalt thickness, base material and base depth, and whether the price includes demolition and haul-off. A quote that only lists a square-foot price is not comparable to one that specifies 3" over 8" of processed gravel.
Book early in the season. Texas crews fill their schedules fast and late-season work gets rushed into cold weather, which is when compaction problems appear.
Paving costs across Texas
Pricing inside Texas is not uniform. The asphalt paving market is set by the metro areas — Houston, Dallas, San Antonio, Austin and Fort Worth — where crew wages, disposal fees and permit costs all run above the state average. Rural counties in Texas typically come in 10 to 20 percent below the metro figure on material-led work, and rather more than that on labour-led work, though long haul distances can claw some of it back.
Contractors working in Texas are licensed or registered through the city building department (Texas does not license general contractors). Before you sign anything, look the company up there and confirm the licence is current, then confirm liability insurance and workers' compensation directly with the insurer named on the certificate. A licence lookup takes two minutes and is the single most useful check a homeowner can make.
Permits are city-issued; Austin and Dallas both enforce impervious-cover limits on residential lots.
What a asphalt driveway costs in each part of Texas
Inside Texas, Houston is the market that sets the top of the range — crews there carry higher wages, disposal fees and permit costs, so a Houston job typically lands around 8 percent above the statewide figure. Work the same job out into rural Texas and you can expect roughly 14 percent below it, provided the site is not a long haul from the nearest asphalt plant. Haul distance is the one thing that can reverse the discount entirely: past about 30 miles the truck time starts to eat the saving.
Quotes inside one metro still vary by 30 to 40 percent between contractors for the same scope, which is why the range above is a range. The cheap quote is usually cheap for a stated reason — thinner base, no compaction testing, no haul-off, or a crew squeezing you in at the end of the season. Ask each bidder to price the same written specification and the spread narrows dramatically.
Repair, resurface or replace in Texas
Resurfacing costs roughly $2.85 to $6.65 per square foot in Texas against $6.65 to $14.25 for a full replacement, so an overlay is about 40 percent of the price of starting again. That makes it the right call when the base is sound and the damage is surface level: oxidation, minor alligatoring, shallow ruts.
It is the wrong call when the failure is structural. Potholes that come back in the same spot, edges crumbling inward, or soft areas that flex under a car all say the base has failed, and highly expansive clay soils and sustained 100 °F summer temperatures in Texas is exactly what causes that. Paving over a failed base buys two or three years and you pay for the tear-out anyway. The honest break-even: if more than about a quarter of the surface shows base-related failure, replace it.
Maintenance is cheap by comparison. Crack filling at $0.95 to $2.85 per linear foot and sealcoating every three to five years will take a Texas driveway from a ten-year life to twenty, and both are a fraction of one percent of the replacement cost per year.
How Texas compares with neighbouring states
Oklahoma, Arkansas price below Texas on the same specification, while New Mexico, Louisiana run higher. That matters if you live near the line: a contractor licensed in both states will often quote the cheaper labour market and travel, though anything more than about 45 minutes from their yard gets loaded back into the price.
Do not let the border tempt you past the licensing question. Whoever you hire must be licensed or registered to work in Texas specifically — the city building department (Texas does not license general contractors) is where you check that, and a licence in the neighbouring state does not carry over.
Texas driveway cost by size
Installed price range at $6.65-$14.25 per sq ft, 3" asphalt over base, no demolition.
| Driveway size | Typical dimensions | TX installed cost |
|---|---|---|
| 400 sq ft | 20 x 20 ft — one car | $2,660 – $5,700 |
| 600 sq ft | 20 x 30 ft — two cars | $3,990 – $8,550 |
| 1,000 sq ft | 20 x 50 ft — two cars plus turnaround | $6,650 – $14,250 |
| 1,500 sq ft | 12 x 125 ft — long rural drive | $9,975 – $21,375 |
| 2,500 sq ft | Large drive with parking apron | $16,625 – $35,625 |
Other paving work in Texas
| Work | TX price per sq ft |
|---|---|
| New asphalt driveway | $6.65 – $14.25 |
| Resurfacing / overlay | $2.85 – $6.65 |
| Tear-out and haul-off | $0.95 – $3.33 |
| Sealcoating (two coats) | $0.14 – $0.33 |
| Recycled asphalt millings | $1.90 – $4.75 |
Texas asphalt driveway cost by metro area
Metro figures are the statewide installed range scaled by local labour, disposal and permit costs. Planning estimates, not quotes.
| Market | Installed per sq ft | 600 sq ft | 1,000 sq ft |
|---|---|---|---|
| Houston metro | $7.18 – $15.39 | $4,309 – $9,234 | $7,182 – $15,390 |
| Dallas metro | $6.98 – $14.96 | $4,190 – $8,978 | $6,983 – $14,963 |
| San Antonio metro | $6.85 – $14.68 | $4,110 – $8,807 | $6,850 – $14,678 |
| Austin metro | $6.78 – $14.54 | $4,070 – $8,721 | $6,783 – $14,535 |
| Fort Worth metro | $6.72 – $14.39 | $4,030 – $8,636 | $6,717 – $14,393 |
| Rural Texas | $5.72 – $12.26 | $3,431 – $7,353 | $5,719 – $12,255 |
Texas repair and maintenance prices
TX rates for work on an existing surface, before any mobilisation minimum.
| Job | Unit | TX price |
|---|---|---|
| Crack filling (hot rubber) | per linear ft | $0.95 – $2.85 |
| Pothole patch | each | $114 – $380 |
| Sealcoating, two coats | per sq ft | $0.14 – $0.33 |
| Edge or apron repair | per sq ft | $5.70 – $13.30 |
| Resurfacing / overlay | per sq ft | $2.85 – $6.65 |
| Tear out and replace | per sq ft | $7.60 – $17.58 |
Driveway cost in states bordering Texas
Installed price per square foot, same specification, at each state's own rate.
| State | Installed per sq ft | 600 sq ft job |
|---|---|---|
| New Mexico | $6.79 – $14.55 | $4,074 – $8,730 |
| Oklahoma | $6.30 – $13.50 | $3,780 – $8,100 |
| Arkansas | $6.16 – $13.20 | $3,696 – $7,920 |
| Louisiana | $6.79 – $14.55 | $4,074 – $8,730 |
Frequently asked questions
+How much does an asphalt driveway cost in Texas?
Between $6.65 and $14.25 per square foot installed, so a typical 600 sq ft two-car driveway runs $3,990 – $8,550. Demolition of an existing surface is extra.
+Is asphalt cheaper than concrete in Texas?
Yes — asphalt typically costs 40-50% less to install than concrete. Concrete lasts longer with less maintenance, but asphalt is faster to install, easier to repair and far more forgiving of ground movement.
+When is the best time to pave in Texas?
Year-round. Booking early in that window gets you better crews and better compaction weather than a late-season rush job.
+How thick should the gravel base be for a driveway in Texas?
Because of Texas's highly expansive clay soils and sustained 100 °F summer temperatures, contractors here specify 6 to 8 inches of flex base (crushed limestone) — typically TxDOT Grade 1-2 crushed limestone flex base. Skimping on the base is the single most common cause of premature failure in a southern heat climate.
+What type of asphalt mix is best for Texas?
In a Southern Heat zone, the right spec is Stiff PG 70-22 binder against high-temperature deformation, over stabilised subgrade. Ask any contractor to name the binder grade on the quote — if they cannot, they are buying whatever the plant has running that day.
+What goes wrong with driveways in Texas?
The local failure driver is highly expansive clay soils and sustained 100 °F summer temperatures. That shows up as edge cracking and settlement within three to five years when the base is thin or drainage was never graded away from the slab.
+How long will an asphalt driveway last in Texas?
15-25 years with sealcoating every 3-5 years and prompt crack filling. In a Southern Heat zone, highly expansive clay soils and sustained 100 °F summer temperatures shortens that to under 10 years if maintenance is skipped.
+Do I need a licensed paving contractor in Texas?
The city building department (Texas does not license general contractors) handles contractor licensing or registration for Texas. Check the licence is current in the official register, and ask for a certificate of insurance naming you before work starts.
+Do I need a permit in Texas?
Permits are city-issued; Austin and Dallas both enforce impervious-cover limits on residential lots.
+Are prices different across Texas?
Yes. Houston, Dallas, San Antonio, Austin and Fort Worth set the top of the range because labour, disposal and permit costs are highest there. Rural parts of Texas typically run 10 to 20 percent below those figures, unless the site is a long haul from the nearest plant or supply yard.
+How much does a asphalt driveway cost in Houston?
Around $7.18 to $15.39 per square foot installed, so a 600 square foot job in Houston runs roughly $4,309 – $9,234. Houston sits above the Texas statewide average on labour, disposal and permit costs.
+Is it cheaper to resurface or replace a driveway in Texas?
Resurfacing costs about 40 percent of a replacement in Texas — $2.85 to $6.65 per square foot against $6.65 to $14.25. It is worth it only if the base is sound. Once more than a quarter of the surface shows base failure — recurring potholes, crumbling edges, soft flexing areas — replacement is the cheaper option over ten years.
+What does driveway repair cost in Texas?
Crack filling runs $0.95 to $2.85 per linear foot and a pothole patch $114 to $380 in Texas. Most contractors apply a minimum call-out of a few hundred dollars, so it pays to bundle repairs into one visit.
+Is it cheaper to build in a state bordering Texas?
Oklahoma, Arkansas price below Texas on the same specification. Near a state line that can be worth getting a quote from a crew based across it, as long as they are licensed to work in Texas and the travel is short enough not to be priced back in.
+Are Texas prices different in rural areas?
Yes — rural Texas typically runs around 14 percent below the metro figure, roughly $5.72 to $12.26 per square foot installed. Long haul distance from the nearest asphalt plant can cancel that saving out.